SURREY FIRE SAFETY HOUSE

Height: 11'4 Int. 96" Hitch weight: 840# Axle weight: 6080#

SIDEWALL CONSTRUCTION:

Standard RV 2x2 and 2x3 members on 16"on center. Bonded to 5/32 plywood paneling for high strength and lightweight. Hand cut fiberglass insulation in the sidewalls.

EXTERIOR:

The exterior of the Safety House is white in color and is a heavy .024 aluminum mesa

The unit shall have tandem 4" drop axles 5,200# each with equalizing suspension with standard springs. 4 wheel electric brakes will be utilized Mfg. Hays or equal. Type 12' x 2 1/4". A brake away switch will be attached to the frame as an emergency stop, in the unlikely event of a unit separation.

TIRES AND WHEELS

Tires will be radials ST225/75R15, The tires are mfg. for trailers, offering special sidewall construction to reduce sway while towing. The tires will be mounted on 6 lug white sport mod wheels, with center caps and lug nut covers.

ROOF:

A one piece aluminum roof over 2x6 truss rafters, with a limited 10 year warranty.

FLOOR:

Floor joist are heavy duty 2x4 on 12" center rather than the typical 2x3 and 16' on center. This construction technique offers a strong floor and allows us to provide 25% more floor joist.

The floor is constructed of 5/8" tongue and groove exterior plywood. The floor covering will be carpet with 1/2" thick rebond pad. Vinyl hard goods will be in the basement storage area as well as the generator storage compartment. The floor will be fully insulated and the under belly will be covered with a heavy duty vinyl weather seal.

LIGHTS INTERIOR:

12 volt lights in the ceiling shall be fluorescent (except control room) and connected to wall switches. 12 volt dome lights shall be used in storage compartments and under cabinets as needed. Wall lights shall be located at the fire place ( except with severe weather option)

BENCH SEATING:

All of the bench seats are to be covered with carpet and offer storage inside.

HEAD BUMP PADS:

Head bump pads shall be in place on all outside doors and escape training windows

LIGHTS EXTERIOR:

3 -12 volt porch lights shall be in place. 2 on the door side and one on the rear. Standard ICC lights will be in place. An upper body Brake light and turn signals shall be in place as an added safety feature. A hook up light will be attached to the power tongue jack. A 12 volt power source with a on/off switch, will be pre wired from the control room to the rear roof top for a strobe light.

WINDOWS:

All exterior windows are heat treated safety glass. The RV style windows are sliding windows and do not crank out. These windows eliminate injury by walking into a protruding window frame The escape training windows located in each bedroom shall be 40 x 45 sliders. The balance of the windows are RV slider type with screens. A 3' X 3' picture window shall be in place in the control room, with screen and mini blind. Valances and curtains are in place with the exception of on the escape sliders. The control room shall have 2 observation ports with Plexiglas windows and hinged privacy doors.

TV CABINET: A TV cabinet and slide-out shelf is provided on the awning side of the unit. A slide out shelf will be in place. This allows the tv position to be adjusted to accommodate changing light conditions

FIREPLACE:

A electric fireplace shall be located in the kitchen for safety training. It will have a screen, simulated brick face wooden mantel and a simulated stone hearth. A on/off switch shall be located on the wall next to the fireplace. The fireplace shall have a crackle sound.

KITCHEN:

The kitchen shall have a functional stove, stainless steel sink, exhaust hood with light and microwave. The stove shall have a shut off in the gas supply line. Fresh water is provided to the sink through a city water hook up on the outside of the unit.

A space and outlet for a refrigerator shall be provided. A wall mounted 911 training phone will be located in the kitchen as well as a fireplace.

CONTROL ROOM:

A control room will be provided allowing control of many educational functions.

A hands free 911 telephone system will be in place, as well as control switches for smoke alarms. On/off switches for electric hot doors, controls of smoke generator and smoke routing valves, as well as a smoke ready light from bedroom #2 shall be installed. The control room will provide a location for installation of optional TV camera equipment or PA equipment. The 110 volt circuit breakers, and power converter shall be in the control room. A master switch will control interior lights.

A picture window with screen and mini blind will be included to provide increased comfort for control room personnel.

BEDROOM #1:

Bedroom #1 will be located in the front of the unit on the main level offering full education capability for handicap and wheel chair bound individuals. A 36" entrance door will be in place, as well as a bed, a location to install an optional lower level heated door, and a sliding escape window. The escape window will be equipped with a semi motionless chain escape ladder allowing for egress training with commercially available equipment. Simulated smoke can be provided to the room as well as an exhaust fan to remove smoke. The fan on/off switch shall be in the room and can be controlled directly by the instructor. A heated door, a smoking door and a Hot Knob are options for this room

BEDROOM#2:

Bedroom #2 shall be slightly elevated in the rear of the unit. 3 steps will lead to bedroom#2 which will have a 6'1" ceiling height. An electric heated door will be installed as well as a bed, smoke ducting, 110 volt smoke alarm and dual exhaust fans. Fan control and smoke alarm control will be from the bedroom by the instructor. Installation of these controls in the bedroom allows for a faster cycle of students by maximizing the use of time. A sliding escape window will be in place as well as a semi motionless chain ladder allowing egress training with commercially available equipment.

GENERATOR STORAGE COMPARTMENT:

A generator storage compartment shall be provided on the off door side of the unit. The compartment shall have lights and be constructed in a way that allows no lift unloading of the generator. There will be locks on the compartment allowing secure storage and protection from the weather.

WHEEL CHAIR RAMP & STORAGE:

A wheel chair ramp & storage compartment will be located on the off door side of the unit. The compartment will be equipped with locks for secure storage.

OUTSIDE STORAGE:

Outside storage will be accessible from the off door side rear and the curb side of the unit. A light will be located in the compartment. Doors will be equipped with locks.

110 VOLT POWER:

110 volt power will be provided through a standard 30 amp RV plug on a 25' cord

circuit breakers are provided in the distribution panel located in the control room. All wall outlets are 110 volt with ground fault protection near the sink and outside outlets.

12 VOLT POWER:

12 volt power will be provided by a frame mounted deep cycle (Interstate Battery) or through a 55 amp solid state power converter mfg by Elixir or equal. This unit will handle all of the 12 volt power demand by converting 110 volt AC power to 12 volt DC power. The power converter has a built in, self regulating, battery charger. This charger will maintain a full operational charge of the frame mounted battery automatically.

BATTERY CUT OFF

A switch is provided to shut the battery down for storage. This eliminates a dead battery from accidentally leaving on a light during storage. Your battery will be charged and ready to go.

BACK UP BEEPER

An audible tone will be heard at the rear of the safety house warning any one in the area that the unit is moving in reverse. (The tow vehicle must be properly wired to activate this alarm)

HEATING AND COOLING:

Heat is provided by a forced air furnace rated at 35,000 btu. Heat will be distributed evenly through out the unit by use of heat ducts. A central air conditioning system shall be in place.

The standard air unit is rated at 13,500 btu. A centrally located thermostat will allow consistent temperatures to be maintained. (see option list for up-grades)

ELECTRIC OUTLETS:

Control room-5 Kitchen-4 Bedroom #1-4 Bedroom #2-4 Exterior -2 (1 front. & 1 rear)

ELECTRIC HEATED DOOR:

A heated door shall be in place for a hands on demonstration of how to check for a hot door. The electric hot door is to be fully adjustable , with temperature limit switch

protection.

AWNING : A 21 ft awning is provided on the road side of the unit covering the door.

SMOKE GENERATOR :

A smoke machine shall be provided, with a gal. of non toxic, water base smoke fluid.

911 TELEPHONE

A 911 training phone shall be in place, The system shall allow hands on training in the proper use of the 911 system. The student will be able to talk with the unseen control room operator. Also the system shall have the ability for call back from control room to student. A outside telephone jack will be installed on the door side of the unit. This phone jack will allow neighbors house 911 training

POWER ROOF VENTS: Power roof vents shall be found in the following locations:

control room-1, kitchen-2 (1 used for optional air conditioning installation),

bedroom #1-1, bedroom #2-1.

HITCH JACK

A 12-volt power tongue jack manufactured by Barker Mfg. will be in place. The unit will have manual back up capability as well as a hookup light.

STABILIZER JACK

------------------------------------------------------------------------------------------------------

SURREY FIRE SAFETY HOUSE

Model # 33B-LTD 2 BEDROOM

Height: 11'4 Int. 96" Hitch weight: 880# Axle weight: 6450#

SIDEWALL CONSTRUCTION:

Standard RV 2x2 and 2x3 members on 16" on center. Bonded to 5/32 plywood paneling for high strength and lightweight. Hand cut fiberglass insulation in the sidewalls.

EXTERIOR:

The exterior of the Safety House is white in color and is made of fiberglass.

The unit shall have tandem 4" drop axles 5,200# each with equalizing suspension with standard springs. 4 wheel electric brakes will be utilized Mfg. Hays or equal. Type 12' x 2 1/4". A brake away switch will be attached to the frame as an emergency stop, in the unlikely event of a unit separation.

TIRES AND WHEELS

Tires will be radials ST225/75R15. The tires are mfg. for trailers, offering special sidewall construction to reduce sway while towing. The tires will be mounted on 6 lug white sport mod wheels, with center caps and lug nut covers.

ROOF:

A 1 piece TPO roof is provided bonded to plywood underlayment . Tapered 2x6 roof trusses provide a crown to the roof eliminating puddling . 4 roof vents are in place.

FLOOR:

Floor joist are heavy duty 2x4 on 12" center rather than the typical 2x3 and 16' on center. This construction technique offers a strong floor. The floor is constructed of 5/8" tongue and groove exterior plywood. The floor covering will be carpet with 1/2" thick rebond pad. Vinyl hard goods will be in the basement storage area as well as the generator storage compartment. The floor will be fully insulated and the under belly will be covered with a heavy duty vinyl weather seal.

LIGHTS INTERIOR:

12 volt lights in the ceiling shall be fluorescent (except control room) and connected to wall switches. 12 volt dome lights shall be used in storage compartments and under cabinets as needed. Wall lights shall be located at the fire place ( except with severe weather option)

BENCH SEATING:

All of the bench seats are to be covered with carpet and offer storage inside.

HEAD BUMP PADS:

Head bump pads shall be in place on all outside doors and escape training windows

LIGHTS EXTERIOR:

3 -12 volt porch lights shall be in place. 2 on the door side and one on the rear. LED ICC lights will be in place. They have proven to be maintenance free and are rated for 200,000 hr. life. An upper body Brake Light and turn signals shall be in place. A hook up light will be attached to the power tongue jack. A 12 volt power source with a on/off switch, will be pre wired from the control room to the rear roof top for a strobe light.

WINDOWS:

All exterior windows are heat treated safety glass. The escape training windows located in each bedroom shall be 40 x 45 sliders. The balance of the windows are radius RV slider type with screens. A 3' X 3' picture window shall be in place in the control room, with screen and mini blind. Valances and curtains are in place with the exception of on the escape sliders. The control room shall have 2 observation ports with plexiglas windows and sliding privacy doors.

FIREPLACE:

An electric fireplace shall be located in the kitchen for safety training. It will have a screen, simulated brick face wooden mantel and a simulated stone hearth. An on/off switch shall be located on the wall next to the fireplace. The fireplace shall have a crackle sound.

KITCHEN:

The kitchen shall have a functional stove, stainless steel sink, exhaust hood with light and microwave. The stove shall have a shut off in the gas supply line. Fresh water is provided to the sink through a city water hook up on the outside of the unit.

A space and outlet for a refrigerator shall be provided. A wall mounted 911 training phone will be located in the kitchen as well as a fireplace.

CONTROL ROOM:

A control room will be provided allowing control of many educational functions.

A hands free 911 telephone system will be in place, as well as control switches for smoke alarms. On/off switches for electric hot doors, controls of smoke generator and smoke routing valves, as well as a smoke ready light from bedroom #2 shall be installed. The control room will provide a location for installation of optional TV camera equipment or PA equipment. The 110 volt circuit breakers, and power converter shall be in the control room. A master switch will control interior lights.

A picture window with screen and mini blind will be included to provide increased comfort for control room personnel.

BEDROOM #1:

Bedroom #1 will be located in the front of the unit on the main level offering full education capability for handicap and wheel chair bound individuals. A 36" entrance door will be in place, as well as a bed, a location to install an optional lower level heated door, and a sliding escape window. The escape window will be equipped with a semi motionless chain escape ladder allowing for egress training with commercially available equipment. Simulated smoke can be provided to the room as well as an exhaust fan to remove smoke. The fan on/off switch shall be in the room and can be controlled directly by the instructor. A heated door, a smoking door and a Hot Knob are options for this room

BEDROOM #2:

Bedroom #2 shall be slightly elevated in the rear of the unit. 3 steps will lead to bedroom#2 which will have a 6'1" ceiling height. An electric heated door will be installed as well as a bed, smoke ducting, 110 volt smoke alarm and dual exhaust fans. Fan control and smoke alarm control will be from the bedroom by the instructor. Installation of these controls in the bedroom allows for a faster cycle of students by maximizing the use of time. A sliding escape window will be in place as well as a semi motionless chain ladder allowing egress training with commercially available equipment.

GENERATOR STORAGE COMPARTMENT: A generator storage compartment shall be provided on the off door side of the unit. The compartment shall have lights and be constructed in a way that allows no lift unloading of the generator. There will be locks on the compartment allowing secure storage and protection from the weather.

WHEEL CHAIR RAMP & STORAGE:

A wheel chair ramp & storage compartment will be located on the off door side of the unit. The compartment will be equipped with locks for secure storage.

OUTSIDE STORAGE:

Outside storage will be accessible from the off door side, rear and the curb side of the unit. A light will be located in the compartment. The doors will be equipped with locks.

110 VOLT POWER:

110 volt power will be provided through a standard 30 amp RV plug on a 25' cord

circuit breakers are provided in the distribution panel located in the control room. All wall outlets are 110 volt with ground fault protection near the sink and for outside outlets.

12 VOLT POWER:

12 volt power will be provided by a frame mounted deep cycle (Interstate Battery) or through a 55 amp solid state power converter mfg by Elixir or equal. This unit will handle all of the 12 volt power demand by converting 110 volt AC power to 12 volt DC power. The power converter has a built in, self regulating, battery charger. This charger will maintain a full operational charge of the frame mounted battery automatically.

BATTERY CUT OFF

A switch is provided to shut the battery down for storage. This eliminates a dead battery from accidentally leaving on a light during storage. Your battery will be charged and ready to go.

BACK UP BEEPER

An audible tone will be heard at the rear of the safety house warning any one in the area that the unit is moving in reverse. (The tow vehicle must be properly wired to activate this alarm)

HEATING AND COOLING:

Heat is provided by a forced air furnace rated at 35,000 btu. Heat will be distributed evenly through out the unit by use of heat ducts. A centrally located thermostat will allow consistent temperatures to be maintained. The unit will be prewired for air conditioning. (see option list)

ELECTRIC OUTLETS:

Control room-5 Kitchen-4 Bedroom #1-4 Bedroom #2-4 Exterior -2 (1 front. & 1 rear)

ELECTRIC HEATED DOOR:

A heated door shall be in place for a hands on demonstration of how to check for a hot door. The electric hot door is to be fully adjustable, with temperature limit switch

protection.

AWNING

A 21 ft awning is provided on the road side of the unit covering the door.

SMOKE GENERATOR :

A smoke machine shall be provided, with a gal. of non-toxic, water base smoke fluid.

911 TELEPHONE

A 911 training phone shall be in place, The system shall allow hands on training in the proper use of the 911 system. The student will be able to talk with the unseen control room operator. Also the system shall have the ability for call back from control room to student. A outside telephone jack will be installed on the door side of the unit. This phone jack will allow neighbors house 911 training

POWER ROOF VENTS: Power roof vents shall be found in the following locations:

control room-1, kitchen-2 (1 used for optional air conditioning installation),

bedroom #1-1, bedroom #2-1.

HITCH JACK

A 12-volt power tongue jack manufactured by Barker Mfg. will be in place. The unit will have manual back up capability as well as a hookup light.

STABILIZER JACK

Length: 33' 8" Width: 8"0" GVW: 7,330#

FRAME CONSTRUCTION

Frame 2x8 high strength (Bull Moose)® double tube steel rails. Welded battery rack on tongue with 4x4 steel rear bumper and rear skid bars for add'l protection. 4 crank down stabilizer jacks will be mounted to the frame. A power tongue jack will be provided. Safety chains and rear skid bars are in place.

SIDEWALL CONSTRUCTION

2x3 members 16" on center. Studs are bonded to 5/32 plywood paneling for high strength and lightweight. ABS fenders with galvanized wheel pans. Hand cut fiberglass insulation in sidewalls with an R 7 rating.

4 BAL or equal, crank down stabilizer jacks shall be frame mounted. These jacks will stabilize the unit and eliminate suspension travel while occupied.

Due to the constant refinement and development of the Safety House the specifications may change with out notice